This set of equipment is designed for the production of raincoats from a tubular polymer film. The set includes the following processing units: hot and cold cutting, edge trimming, and hood fabrication. The set can be supplemented with additional processing components (e.g., a snap-fastener attachment unit).<\/p>\n
The equipment is designed for operation within enclosed production facilities (climate category UHL4), with an ambient air temperature ranging from +5\u00b0C to +35\u00b0C and humidity up to 70%.<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
This equipment set is designed for the production of raincoats from polymer film tubing. The set includes the following processing units: hot and cold cutting, edge trimming, and hood fabrication. The set can be supplemented with other processing components (such as a unit for attaching snap buttons).<\/p>\n
The equipment is designed for operation within enclosed production facilities (climate category UHL4), with an ambient air temperature ranging from +5\u00b0C to +35\u00b0C and humidity up to 70%.<\/p>\n
<\/p>\n
This equipment serves as a processing component within a production line for manufacturing raincoats from polymer film. It is designed to prepare the main body of a raincoat by hot-cutting it from a roll of tubular polymer film.<\/p>\n
<\/p>\n
<\/p>\n
The unit is a welded, floor-standing structure consisting of a frame (1) that supports the hot-cutting table (2), the adjustment unit (4), the roll holder (5), and the pneumatically operated crossbar (3).<\/p>\n
The operator loads a roll of tubular film onto the roll holder (5) and pulls the edge of the film across to the opposite side of the table (2), positioning it over the hot-cutting surface. Upon pressing a foot pedal, the pneumatically operated clamping crossbar (3) descends, securing the film against the surface of the table (2). The polymer film is cut using a hot-cutting process (thermal cutting combined with simultaneous welding) according to a specific pattern. Once the hot-cutting duration\u2014set on the control unit (4)\u2014has elapsed, the crosshead (or clamping beam) rises, allowing the operator to remove the finished item and any excess material (trim\/scrap).<\/p>\n
The duration of the hot-cutting process is determined empirically and depends on the specific characteristics of the film.<\/p>\n
The cycle then repeats.<\/p>\n
<\/p>\n
Designed for cutting the front section of a raincoat and forming the neckline opening.<\/p>\n
<\/p>\n
<\/p>\n
The unit consists of a welded structure comprising a frame (1) that supports the cold-cutting table (2), the control unit (4), and a crosshead (3) equipped with a magnetic drive.<\/p>\n
The operator stretches the lower part of the raincoat material over the cold-cutting table (2) and lowers the crosshead (3). An electromagnet secures the crosshead (3) firmly against the table (2), holding the raincoat blank securely in place. The operator then uses a knife, guided by a template, to cut the front section and the neckline opening. Press the button on the control unit (4); the crosshead (3) rises, and the garment cover is removed.<\/p>\n
The cycle repeats.<\/p>\n
<\/p>\n
<\/p>\n
This equipment set is designed for the production of raincoats from tubular polymer film. The set includes modules for hot and cold cutting, edge trimming, and hood fabrication. It can be further equipped with additional components (such as a snap-fastener attachment unit).<\/p>\n
The equipment is intended for operation within enclosed production facilities (climate category UHL4), with an ambient air temperature ranging from +5\u00b0C to +35\u00b0C and humidity up to 70%.<\/p>\n
<\/p>\n
This unit serves as a component of the equipment set used for manufacturing raincoats from polymer films.<\/p>\n
Designed for preparing the base material for rain capes by hot-cutting tubular polymer film.<\/p>\n
<\/p>\n
<\/p>\n
The unit is a floor-standing welded structure comprising a frame (1) that supports the hot-cutting table (2), control unit (4), roll holder (5), and a pneumatically-actuated crossbar (3).<\/p>\n
The operator mounts the roll of tubular film onto the holder (5) and pulls the edge of the film across to the opposite side of the table (2) so that the film lies over the hot-cutting surface. Upon pressing a foot pedal, the pneumatically-actuated clamping crossbar (3) descends, pressing the film firmly against the surface of the table (2). The polymer film is then hot-cut\u2014a process involving thermal cutting combined with simultaneous sealing\u2014according to the required pattern.<\/p>\n
Once the hot-cutting time\u2014set on the control unit (4)\u2014has elapsed, the crosshead rises, allowing the operator to remove the finished product and clear away any residue (oil).<\/p>\n
The duration of the hot-cutting process is determined empirically and depends on the specific characteristics of the film.<\/p>\n
The cycle then repeats.<\/p>\n
<\/p>\n
Designed for cutting the front section of a raincoat and forming the neckline opening.<\/p>\n
<\/p>\n
<\/p>\n
The unit features a welded structure comprising a frame (1) that supports the cold-cutting table (2), the control unit (4), and a crosshead (3) equipped with a magnetic drive.<\/p>\n
The operator stretches the lower part of the raincoat over the cold-cutting table (2) and lowers the crosshead (3). An electromagnet secures the crosshead (3) firmly against the table (2), holding the raincoat blank securely in place. The operator then uses a knife and a template to cut the front section and the neckline opening. Press the button on the control unit (4); the crosshead (3) rises, and the raincoat is removed.<\/p>\n
The cycle repeats.<\/p>\n
<\/p>\n
In addition to serving as a component of the production line for manufacturing raincoats, this equipment can also be used for the production and sealing of bags made from polymer films. Designed for trimming the edges of a raincoat blank, as well as for fabricating and welding a hood onto the garment.<\/p>\n
<\/p>\n
<\/p>\n
The unit features a welded frame (1) that houses the support base (2), control unit (4), crosshead (3) with welding tools, roll holders (5), and a foot pedal (6).<\/p>\n
To trim the edges of a raincoat blank, the operator places the edge between the support base (2) and the clamping crosshead (3), then presses the foot pedal (6) to perform the cut using a mechanical blade mounted on the crosshead (3).<\/p>\n
To weld a hood, the operator positions the hood and the raincoat blank between the support base (2) and the clamping crosshead (3)\u2014which contains the welding elements\u2014and presses the foot pedal (6). The machine then performs the welding process according to the parameters set on the control unit (4). After the audible signal, the operator releases the pedal (6) and removes the hooded raincoat.<\/p>\n
<\/p>\n
<\/p>\n
12-month warranty
\nPost-warranty service and maintenance<\/p>\n","protected":false},"excerpt":{"rendered":"
This set of equipment is designed for the production of raincoats from a tubular polymer film. The set includes the following processing units: hot and cold cutting, edge trimming, and hood fabrication. The set can be supplemented with additional processing components (e.g., a snap-fastener attachment unit). The equipment is designed for operation within enclosed production […]<\/p>\n","protected":false},"author":2,"featured_media":4758,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"inline_featured_image":false,"ngg_post_thumbnail":0,"footnotes":""},"categories":[37],"tags":[],"class_list":["post-4757","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-custom-equipment"],"acf":[],"yoast_head":"\n